Coat Pattern Women: Sew the Shawl Collar Coat Step by Step

A long, fully lined coat with a shawl collar, one button and in-seam pockets, in sizes 34 to 56, with our free sewing tutorial.

By · Updated

Woman walking toward the camera in a long mustard wool coat with a shawl collar and a single button, worn with dark ankle boots, photographed head to toe.

This coat pattern for women makes a long, fully lined shawl collar coat with a one-button closure and pockets set into the side seams, in sizes 34 to 56. The front and collar are cut in one piece, and the coat is rated 3 out of 4 for difficulty. The free tutorial below covers the full sewing instructions: coat lengths, fabric and lining amounts, pattern pieces and cutting layouts, then the 11 steps with diagrams.

The shawl collar coat: a long, lined coat pattern for women

This coat pattern for women makes a long, lined coat with a shawl collar and a one-button closure. The whole sewing tutorial is free on this page; you'll find our other projects on the free sewing tutorials home page.

The front and collar are cut in one piece, with bust darts in the shoulder seam. The pockets are set into the side seams. The sleeves are two-piece (upper sleeve and under sleeve). The coat is fully lined, with an ease pleat at the center back of the lining.

Difficulty: 3 out of 4. Sizes 34 to 56.

Technical drawings of the shawl collar coat, front and back, showing the one-piece front and collar and the one-button closure.
Technical drawings: front and back.

The finished coat

These photos of the finished coat show the result to aim for from every angle.

Woman wearing a long mustard wool coat with a shawl collar and a single button, sewn from this coat pattern for women, hands on her hips.
Front, buttoned.
Front view of the long shawl collar coat, buttoned, with arms relaxed by the sides.
Front, arms by the sides.
Three-quarter back view of the shawl collar coat, showing the back and the two-piece sleeves.
Back, three-quarter view.
The shawl collar coat worn open, with the collar and front facing visible.
Worn open.
Model wearing the shawl collar coat with one hand on her hip.
Hand on the hip.
Model with both hands in the in-seam side pockets of the coat.
Hands in the side pockets.

The coat as worn

A long coat that goes with every winter outfit.

The long shawl collar coat worn buttoned, seen from the front.
Buttoned, front view.
The shawl collar coat worn with one hand in a side pocket.
Hand in the pocket.
Woman standing on a cobbled city street in the long mustard shawl collar coat, worn with dark ankle boots.
In town.

Sizes 34 to 56 and coat length

The tables below give the length of the coat in each size, from 34 to 56.

Center back length (in cm, without collar)

Size343638404244
Length121.5122122.5123123.5124
Size464850525456
Length124.5125125.5126126.5127
Note

Always read all the instructions before cutting the fabric!

Supplies and fabric for the shawl collar coat

Gather your fabric, lining and notions before you start: the list and tables below give everything the coat needs.

Supplies

  • Sewing thread
  • Button: 1
  • Snap fastener (ø 24 mm): 1
  • Snap fastener (ø 15 mm): 2
  • Fusible interfacing: max. 315 cm
  • Lining fabric: see table
  • Fabric (140 cm wide): see table

Fabric length

Size3436-3840-5254-56
Fabric length (in cm)255280300320

Lining fabric length

Size34-4850-56
Lining fabric length (in cm)200235

Which fabric to choose for a long coat?

We chose a medium-weight wool fabric. Go for a fairly thick coating fabric, wool for example. In any case, do not use a stretch fabric.

Pattern pieces and cutting layout

Cut the pattern pieces from your fabric, in the quantities given below.

PieceNameTo cut
AFront2x
BBack2x
CFront facing2x
DBack facing1x on the fold
EUpper sleeve2x
E'Upper sleeve lining2x (from lining)
FUnder sleeve2x
F'Under sleeve lining2x (from lining)
GPocket4x (from lining)
HFront lining2x (from lining)
IBack lining1x on the fold (from lining)
Diagram of the coat pattern pieces A to I: front, back, facings, sleeves, pocket and lining pieces.
Caution

To cut the same piece 2x, cut it through both layers of the fabric folded in half. To cut a single symmetrical piece, place the symbol Fold symbol on the fold of the fabric.

Caution

E and E', F and F' are the same piece on the pattern.

Seam allowances

These seam allowances are included around the pattern pieces if you selected “Cutline” in the layers of the PDF pattern.

PiecesSeam allowances
A, B, E, Fhem: 4 cm — elsewhere: 1 cm
D, ICB: 0 cm (on the fold) — elsewhere: 1 cm
C, G, Hall around: 1 cm
Caution

Remember to transfer all the markings shown on the pattern to the fabric, using notches and tailor's tacks.

Interfacing

Fuse fusible interfacing to the wrong side of the following pieces.

PiecesTo interface
Bhem allowance
A, C, Dthe whole piece

Cutting layout

Caution

The layout below is for fabric 140 cm wide.

Cutting layout for the coat fabric, showing how the outer pieces are placed on the folded fabric.
Fabric: length 255 to 280 cm (sizes 34 to 38) and 300 to 320 cm (sizes 40 to 56).
Cutting layout for the lining fabric, showing the lining, pocket and sleeve lining pieces.
Lining: length 200 cm (sizes 34 to 48) and 235 cm (sizes 50 to 56).

The PDF pattern to print

Overview of the 77 assembled sheetsB · BackD · Back facingE/E' · Upper sleeveI · Back liningG · PocketH · Front liningF/F' · Under sleeveA · FrontC · Front facing
The assembled pattern, scaled down: it shows where each piece lies on the assembled pattern.

The pieces of the shawl collar coat come in the PDF pattern: you print it at home at actual size, on A4 or US Letter paper, then tape the sheets together. It covers every size from 34 to 56, with one layer per size and a “Cutline” layer that adds the seam allowances, plus a test square to check the scale. The sewing tutorial itself stays free on this page.

Download the PDF pattern

How to sew a coat: the shawl collar coat step by step

The coat comes together in 11 steps: front, back, shoulder seams, pockets and sleeves, then the facing and lining, before the button and the final pressing. Each step shows a diagram with its instructions.

Seam allowance

Seam allowances are included in the pattern if you printed the “Cutline” lines: 1 cm all around, 4 cm hem allowance for A, B, E and F, 0 cm at the CB of D and I (on the fold).

Key to the symbols used in the sewing diagrams.
Key to the diagrams.

Step 1 — Front

Front piece A with the points to mark with tailor's tacks.
Diagram 1.1
  1. Mark the points shown on the front (A) with tailor's tacks.
Bust dart stitched in the shoulder seam of front A, folded right sides together.
Diagram 1.2
  1. Fold A right sides together, matching the markings in the shoulder seam, to stitch the bust darts.
  2. Stitch from the markings toward the tailor's tack, tapering to nothing.
  3. Press the darts toward the side seam.
Pocket piece G stitched to the edge of front A, right sides together.
Diagram 1.3
  1. Place the upper (straight) edge of the pocket (G) on the edge of A, right sides together, and stitch.
  2. Press the seam toward G.
  3. Repeat with the other A piece.
The two front pieces joined at the center back collar seam, seam pressed open.
Diagram 1.4
  1. Pin the CB collar seam of the two A pieces right sides together and stitch.
  2. Press the seam open.

Step 2 — Back

Back piece B with the points to mark with tailor's tacks.
Diagram 2.1
  1. Mark the points shown on the back (B) with a tailor's tack.
Center back seam of the two back pieces stitched and pressed open.
Diagram 2.2
  1. Place the CB seam of the two B pieces right sides together, matching the markings, and stitch.
  2. Press the seam open.
Pocket piece G attached to the back B, as on the front.
Diagram 2.3
  1. Attach pocket G to B in the same way as for front A.

Step 3 — Shoulder seams

Neckline of the front and back pinned and stitched between the tailor's tacks, with the corners of A clipped.
Diagram 3.1
  1. Pin the neckline of A and B right sides together, matching seams and tailor's tacks, and stitch between the two tailor's tacks.
  2. Clip diagonally into the corners of A, up to the stitching.
Shoulder seams of front and back stitched, with the neckline seam allowance clipped and pressed open.
Diagram 3.2
  1. Pin the shoulder seams of A and B and stitch, starting at the tailor's tack.
  2. Open out the seam allowances.
  3. Clip into the neckline seam allowance so that the seam curves smoothly.
  4. Trim the seam allowance of A to reduce bulk.
  5. Press the seam open.

Step 4 — Side seams and pockets

Side seam of the coat stitched with the in-seam pocket, pivoting at the tailor's tacks.
Diagram 4.1
  1. Pin the side seams of A and B right sides together, matching the tailor's tacks.
  2. Also pin the pockets onto each other.
  3. Stitch the side seam from the underarm to the first tailor's tack, leave the needle down and pivot the fabric so you can stitch the pocket edge to the second tailor's tack.
  4. Stitch the lower part of the side seam in the same way.
  5. Stitch the pocket a second time between the tailor's tacks, 0.5 cm from the first stitching, to reinforce it.
  6. Press the side seams open and press the pockets toward A.
  7. Clip into the corner of the B pocket, up to the stitching.
  8. Repeat for the other side seam of A and B.

Step 5 — Sleeves

Upper sleeve and under sleeve stitched together on both sides.
Diagram 5.1
  1. Pin the seams on both sides of the upper sleeve (E) and the under sleeve (F), right sides together and matching the markings, and stitch.
  2. Open out the seam allowances.
Sleeve head pinned into the armhole of the coat, with the markings matched.
Diagram 5.2
  1. Pin the sleeve head into the armhole of the coat.
  2. Make sure the markings match.
  3. The single marking on E matches the marking on A; the double marking on F matches the double marking on B.
  4. The single marking at the top of E matches the shoulder seam; the single marking at the bottom of F matches the side seam.
  5. Baste the sleeve first, then stitch, to avoid unwanted puckers.
  6. Press the sleeve head into shape.

Step 6 — Front facing

Front facing C and back facing D with their markings, and the center back seam of the front facings stitched.
Diagram 6.1
  1. Mark the points shown on the front facing (C) and the back facing (D).
  2. Pin the CB seam of the two C pieces and stitch.
  3. Press the seam open.
Back facing D stitched to the neckline of the front facing C, with the corners clipped.
Diagram 6.2
  1. Pin the neckline of D to the neckline of C, right sides together, matching the tailor's tacks.
  2. Stitch between the tailor's tacks.
  3. Clip into the corners of C, up to the stitching.
Shoulder seams of the facings stitched and pressed open.
Diagram 6.3
  1. Pin the shoulder seams of C and D and stitch, starting at the tailor's tack.
  2. Open out the seam allowances.
  3. Clip into the neckline seam allowance so that the seam curves smoothly.
  4. Trim the seam allowance of C to reduce bulk.
  5. Press the seam open.

Step 7 — Back lining

Back lining I folded in half to stitch the ease pleat at the neckline.
Diagram 7.1
  1. Fold the back lining piece (I) in half, right sides together, so that the markings at the neckline line up.
  2. Stitch about 3 cm downward to form an ease pleat.
  3. Then fold the pleat flat so that the CB marking matches the stitched pleat.
Front lining H joined to the back lining I at the shoulder and side seams.
Diagram 7.2
  1. Pin the shoulder seams of the front lining (H) to the shoulder seams of I, right sides together, and stitch.
  2. Also pin and stitch the side seams of H and I, right sides together and matching the markings.
  3. Press the seams toward H.
Facing stitched to the outer edge of the lining, right sides together.
Diagram 7.3
  1. Pin the neckline seam and the side seam of the facing (C/D) to the outer edge of the lining (I/H), right sides together, and stitch.
  2. Press the seam toward the lining (H).

Step 8 — Sleeve lining

Hem of the upper and under sleeve lining pieces cut along the marked cutting line.
Diagram 8.1
  1. Cut the hem of the upper sleeve lining (E') and the under sleeve lining (F') along the cutting line shown.
Sleeve lining pieces stitched together, with an opening left in one seam for turning.
Diagram 8.2
  1. Pin the seams on both sides of E' and F', right sides together and matching the markings, and stitch.
  2. Repeat the previous steps with the other E' and F' pieces, but leave an opening in the seam so you can turn the coat later.
Sleeve lining head pinned into the armhole, with the markings matched.
Diagram 8.3
  1. Pin the sleeve head into the armhole of the garment.
  2. Make sure the markings match.
  3. The single marking on E' matches the marking on H; the double marking on F' matches the double marking on I.
  4. The single marking at the top of E' matches the shoulder seam.
  5. Baste the sleeve first, then stitch, to avoid unwanted puckers.

Step 9 — Bagging the lining

This step joins the outer coat and the lining, then turns the whole coat right side out through the opening left in the sleeve lining.

Outer coat and lining placed right sides together, with the hems pinned and stitched at both ends.
Diagram 9.1
  1. Place the outer coat and the lining right sides together.
  2. Pin the hems and stitch about 5 cm at both ends.
Center front edges and necklines of the coat and lining stitched right sides together.
Diagram 9.2
  1. Place the CF edges and necklines right sides together and stitch.
  2. At the bottom, the front hem facing folds as well.
  3. Press the seam toward C.
Coat turned right side out, with the seam allowance stitched onto the facing below the pin and onto the front above it.
Diagram 9.3
  1. Turn the coat right side out and mark the position of the marking on the outer edge of C with a pin, so that it is visible on the right side.
  2. Stitch the seam allowance of A and C onto C, 3 mm from the seam, from the lower edge to 3 cm from the pin.
  3. Do the same above the pin, but with the seam allowance turned toward the front (A), and stitch onto A, 3 mm from the seam.
Sleeve and sleeve lining slipped into each other, with the sleeve hem seam allowances pulled out through the opening.
Diagram 9.4
  1. Slip the sleeves and sleeve linings into each other as they will sit (wrong sides together, right side out).
  2. Fold under 1 cm of seam allowance at the sleeve hem, on both the outer fabric and the lining.
  3. Put your hand through the opening in the sleeve to catch the seam allowances of the sleeve hem between the 2 layers of fabric and pull them out.
  4. Now you can pin and stitch the sleeve hems right sides together.
  5. Then turn the sleeves right side out.
  6. Now sew the coat and lining together in several places.
  7. Put your hand back through the opening at the sleeve hem and pull out the neckline seam allowances.
  8. Stitch them together.
  9. Also tack the lining and outer together at the shoulders and underarms, with a loose stitch.
Rest of the coat hem pinned and stitched with the coat turned right side in.
Diagram 9.5
  1. Turn the coat so that the right side is inside.
  2. Then pin and stitch the rest of the hem as well.
  3. Turn the coat right side out through the opening in the sleeve.
Opening in the sleeve lining stitched closed.
Diagram 9.6
  1. Now close the opening in the sleeve lining.

Step 10 — Buttonhole and button

Horizontal buttonhole on the right front, button on the left front and snap fasteners positioned on the coat.
Diagram 10.1
  1. Make a horizontal buttonhole in the RF (A) at the tailor's tack and sew the button onto the LF.
  2. Sew on the snap fasteners, leaving 10 cm between them.

Step 11 — Final pressing

The finished shawl collar coat after the final pressing.
Diagram 11.1
  1. Press the coat carefully. And you're done!

Practical tips for sewing your coat

These common sewing techniques complement the instructions above. They change neither the order of the steps nor the measurements in the tutorial.

Before you start

  • Test-stitch on a scrap of the same fabric, in a double layer, to set the stitch length and tension. Also test on the lining, which is more slippery.
  • For a thick coating fabric, use a heavier machine needle than for a lightweight fabric, and change it if it snags.
  • Fusible interfacing: place the adhesive side (rough, shiny) against the wrong side of the fabric. Cover with a pressing cloth and press the iron down without sliding it, section by section. Test first on a wool scrap.
  • Transfer all the markings before removing the paper: notches around the edges, tailor's tacks for the inner points (bust darts, pockets, button and buttonhole).

Shawl collar and facings (steps 3 and 6)

  • The clips in the corners of A (diagonal) and C stop just short of the stitching, without cutting it: this is what lets the corner open out flat.
  • In thick wool, carefully trim the seam allowances indicated: the collar hangs better and does not form a ridge.

Pockets in the side seams (step 4)

  • When pivoting at each tailor's tack, make sure the needle is down in the fabric before turning: the corner stays crisp.
  • The second reinforcing line of stitching between the tailor's tacks protects the pocket, which takes a lot of strain when you put your hands in.

Lining (steps 7 to 9)

  • Do not remove the ease pleat from the back lining: it gives the lining the room it needs when you move your arms.
  • Before stitching the sleeve hems, check that the sleeve and lining are not twisted: the seams should line up.
  • Leave an opening in the sleeve lining just wide enough to turn the whole coat without forcing.

Buttonhole (step 10)

  • First make a test buttonhole on an interfaced wool scrap of the same thickness as the front.
  • Open the buttonhole with a seam ripper, with a pin across the end so you don't cut through the bar tack.

Toile (test garment)

  • Cut pieces A, B, E and F from an inexpensive fabric with a similar body to the real fabric, and sew them together with a long stitch, without lining or finishing.
  • Check: the across-back width and armholes; the sleeve length; the center back length (section 02); the position of the pocket markings for your hands; that you can move your arms freely.
  • Transfer any changes to the paper pattern before cutting the real fabric.

Looking for another winter coat to sew? See also our scarf collar coat tutorial.

Sewing glossary

Here are the definitions of the sewing terms used in this tutorial, to keep at hand while you sew.

TermDefinition
BacktackSecure a seam at its start and end by sewing three stitches backward, then one forward.
BaggingStitch around the edges of two pieces of fabric (or one piece folded double), right sides together, and turn right side out.
BasteJoin several layers of fabric with a hand needle and basting thread using long stitches, or thread-trace certain pattern lines onto the fabric.
Center backThe line marking the middle of the back of the body.
Center frontThe line marking the middle of the front of the body.
DartsBy folding and partly stitching the fabric in certain places, you give your garment more shape. These folds are called darts.
EaseExtra room built into the pattern beyond the exact body measurements to allow enough freedom of movement and comfort.
FacingThe pattern piece used to finish edges such as necklines, armholes, zippers or the center front.
FoldThe fold of the fabric obtained by folding it double.
Fusible edge tapeFusible tape 1 cm wide, cut on the bias and reinforced with a chain stitch. It is used to stabilize curves (necklines and armholes) so they do not lose their shape.
Fusible interfacingAlso called iron-on interfacing. A fine fabric ironed onto the wrong side of certain parts of a garment to stabilize them. For example: for a waistband, a facing or a collar.
MarkingsSome markings are made with notches, small snips cut into the edge of the fabric to show the position of important features (pleats, armholes…). Important points inside the pattern, such as the ends of a dart or the position of a button, buttonhole, pocket or flap…, are marked with a tailor's tack.
OverlockTrim fraying edges with an overlocker (serger) and finish them with an overlock stitch.
PressPress an iron onto a damp cloth, for example to flatten seams or get crisp folds. When pressing, you barely move the iron.
Presser footThe part of your sewing machine under which the layers of fabric are placed and fed through.
Presser-foot widthSewing at presser-foot width means running the edge of the presser foot along the seam or edge being stitched.
Seam allowanceThe extra fabric needed to join two pieces. The amount depends on the finishing method used.
SelvageThe edge of the fabric running along the lengthwise grain.
Stay tapeA strip of fusible tape 1, 1.5 or 2 cm wide used on the wrong side to stabilize straight seams (such as shoulder seams) so the fabric does not stretch.
Straight-grain tape / bias bindingA narrow strip of fabric or tape stitched onto the edge to be finished. As the name says, straight-grain tape is cut on the straight grain and bias binding on the bias.
TrimCut away part of the seam allowance to avoid excess bulk in one place. In corners, the seam allowance is trimmed diagonally so it turns out neatly.

Abbreviations used

AbbreviationMeaning
Ftfront
Bkback
RFright front
LFleft front
RBright back
LBleft back
CFcenter front
AbbreviationMeaning
CBcenter back
SSside seam
YKyoke
WBwaistband
ShSshoulder seam
Lleft
Rright

In the PDF pattern, the pattern sheets are on pages 30 to 106. Print them at actual size, in landscape. You'll find the shawl collar coat PDF pattern in the shop, and another long coat to sew in our plaid coat tutorial.

The PDF pattern for this design : Shawl Collar Coat, 34 – 56

PDF · 34 – 56

The PDF pattern for this design : Shawl Collar Coat

Every piece to print at home at full size, with this guide as a PDF.

Download the PDF pattern

PDF pattern sold in the Marie Lestyle shop.

Frequently asked questions : Shawl Collar Coat

What sizes does this coat pattern for women come in?

The pattern comes in sizes 34 to 56. The center back length, without collar, goes from 121.5 cm in size 34 to 127 cm in size 56. Each size has its own layer in the PDF pattern, so you can print only yours.

How much fabric do I need to sew the shawl collar coat?

With fabric 140 cm wide, you need 255 cm for size 34, 280 cm for sizes 36-38, 300 cm for sizes 40-52 and 320 cm for sizes 54-56. For the lining, plan 200 cm for sizes 34-48 and 235 cm for sizes 50-56.

What fabric is best for this long coat?

Go for a fairly thick coating fabric, wool for example. The coat in the photos is made in a medium-weight wool fabric. In any case, do not use a stretch fabric.

Which notions do I need?

Sewing thread, 1 button, 1 snap fastener (ø 24 mm), 2 snap fasteners (ø 15 mm), up to 315 cm of fusible interfacing, plus your fabric and lining.

How difficult is this coat to sew?

It is rated 3 out of 4 for difficulty. The coat has bust darts, pockets set into the side seams, two-piece sleeves and a full lining that is bagged, all explained in the 11 steps with diagrams.

Are seam allowances included in the pattern?

Yes, if you print the “Cutline” lines: 1 cm all around, 4 cm hem allowance for pieces A, B, E and F, and 0 cm at the center back of D and I, which are cut on the fold.

More tutorials